HEAVY EQUIPMENT is a big investment — especially if it’s an excavator you rely on for timber harvesting and processing. To maximize that investment and avoid a breakdown and downtime, regular inspections and maintenance are critical.
More specifically, taking good care of your excavator undercarriage is essential. The undercarriage not only supports the total weight of the machine, but it bears the brunt of rough conditions. It also happens to be the most expensive part of an excavator.
Cold winter temps make undercarriage inspection even more important because freezing temps can wreak havoc on weak components.
The expected life of an excavator’s undercarriage largely depends on how the machine is used. For example, excavators working on a slope tend to show more wear on one side than the other.
The technicians at your dealership are great resources for full undercarriage inspections, but your own technicians and operators can and should conduct a visual inspection at least once a week or every 40 operating hours.
Keep in mind that visual inspections should not replace regularly scheduled management. Proper undercarriage management entails measuring, tracking wear, replacing worn components and swapping component positions to extend the total undercarriage life. You’ll need conversion charts for each brand you use to convert them to percent worn.
Here are five tips for taking care of your excavators’ undercarriage.
Clean before inspecting
To properly inspect a machine, make sure it is somewhat clean for the sake of accuracy. Although it may take a little time, cleaning the undercarriage regularly will keep it in better condition, make it easier to spot issues earlier, and reduce wear on the components.
In cold temperatures, this step is even more important because frozen mud can be like concrete — difficult to chisel or pry out. Plus, any exposure to salt brine could increase the risk of corrosion. Hose down the tracks, undercarriage, driveline, articulation joints and steer cylinders before ending your day to make sure mud doesn’t freeze into place overnight.
1. Document each inspection
Another thing that may sound a little tedious but is very important is to document every inspection. This will prevent unanswerable questions down the line if someone needs to determine when an issue may have started, how much the tracks were adjusted or other helpful details.
Some OEMs offer checklists or worksheets that can make this easier and offer more detail on what to look for with each component.
If you’re going to hop in and get to work after your walk-around, start at the front of the cab. By the time you make the full loop, you’re right where you need to be. Examine everything thoroughly, looking up, down, left and right.
2. Check track tension
Be sure to measure the track tension and document the results. Adjust the tension if necessary and remember to document this, too. You can find the correct track tension for your particular machine in the operator manual.
Carefully examine the track chain and shoes, inspecting the track pads for damage or loose bolts and the chain for any frozen links.
3. Check all components
For a telltale sign that an undercarriage is getting worn out, check the sprocket — the thinner the teeth get, the more worn it is. If they get to a point where it looks like you could shave with them, they’re shot. That’s usually an indicator that the rest of the link assembly needs to be replaced as well.
Carefully check the links for cracks, spalling, side wear, wear on the pin boss or waving. You can also count the links to see if any were removed in an effort to tighten the undercarriage. If someone made it too tight, that will cause problems down the road.
Measure the pins and bushings to see if they’re stretched out. Bushings are often under a considerable load at the sprocket’s six o’clock position, and that will distort them over time. If you run your hand over the bushings in between the links, you should be able to feel whether they are U-shaped (stretched out) versus circular (good to go). If you reach up past the bushings and can touch or see the pins in the center, they should be replaced.
Check for corrosion and pitting on all components — over time, these issues will make the metal more brittle and prone to bigger problems.
4. Check wear distribution
The last step is to compare the two sides of the undercarriage assembly to each other. Does one side show more wear than the other?
If your checklist/worksheet doesn’t have one, it may be smart to add a section where you can document the wear on each track like this:
If one side is more worn down than the other, show this by marking that side further from the center but still relative to the wear on the better side.
Don’t forget: In slick winter conditions, tracks can get quite slippery. Keep them clean and well-maintained for maximum safety.
5. Protect Your Investment
If you’re ever unsure of what you’re looking at or what might need to be done, your dealer can help.
Buying an excavator with warranty coverage for the undercarriage is another good way to ensure that the components stay in good working order. Some OEMs offer extended warranties that cover customer-purchased replacements and/or dealer-installed undercarriages.
A good machine walk-around should take about three to five minutes. That is not too much to ask when we’re talking about the most expensive elements of a machine that you rely on. Undercarriage inspections can greatly reduce the risk of an unexpected and costly breakdown, so don’t skip this important weekly task.
(Chad Welborn is a Certified Used Equipment Service Manager for Volvo Construction Equipment. He can be reached via email at chad.welborn@volvo.com.)














0 Comments